Antec LanBoy Air Blue Bedienungsanleitung

LA NBO Y AI R THE MOST MODULAR, MOST CUSTOMIZABLE OPEN-AIR CHASSIS US E R MA N U A L

10 2.2 INTERNAL 3.5” DEVICE INSTALLATION The LanBoy Air utilizes Antec’s revolutionary AirMount™ suspension HDD mounting system. This sys

11 2.3 EXTERNAL 5.25” DEVICE INSTALLATION There are three externally accessible 5.25” drive bays. Drives can be mounted in three possi

12 1. Insert the rubber grommets into the mounting holes, with the larger portion of the grommet facing the top of the case (Figure 12). 2. Lay the

13 4. Remove the four screws holding the PSU mount in place. Lift and remove the mount, moving it towards the front of the chassis (Figure 18).

14 5. Working with the right side of the chassis, remove the two screws securing each of the rails that the motherboard slides on. Remo

15 8. Once you have secured the rails and PSU mount, the chassis should now look similar to Figure 22. 2.6 MO

16 1. With the motherboard tray on a flat surface, lay the motherboard on the tray and align it with the standoff holes on the motherboard tray a

17 9. Slide the motherboard tray halfway into the chassis along the rails. Connect your drive bay devices to the motherboard and then slide the mothe

18 2.8 CABLE MANAGEMENT There is a cable management area between the motherboard tray and right side panel, as well as cable ties located

19 FRONT I/O PORTS SECTION 3

2 LANBOY AIR USER’S MANUAL Congratulations on your purchase of the Antec LanBoy Air. The LanBoy Air is the most modular, most customizable open-air

20 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Gro

21 3.4 FRONT PANEL GROUND WIRE INSTALLATION The LanBoy Air includes a grounding wire for the front panel ports. This wire should be atta

22 3.6 REWIRING MOTHERBOARD HEADER CONNECTIONS There may come a time when you need to reconfigure the pin-out of a motherboard header co

23 COOLING SYSTEM SECTION 4

24 4.1 INCLUDED FANS Standard fans on the LanBoy Air: A –2 x 120 mm front variable speed fans B – 2 x 120 mm side

25 120MM FAN SPECIFICATIONS: Size: 120 x 25mm two-speed fan Rated Voltage: 12V DC Operating Voltage: 10.8V ~ 13.2 V Speed Input Current Ai

26 4.4 OPTIONAL FANS The LanBoy Air can accommodate up to ten additional 120 mm fans in four different locations: 1. Two additional fans

27 Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterd

3 TABLE OF CONTENTS SECTION 1: INTRODUCTION 1.1 Getting to Know your Chassis ...

4 INTRODUCTION SECTION 1

5 1.1 GETTING TO KNOW YOUR CHASSIS Drive Bays Hardware Mounts 1 5.25" drive bays default location 10 Removable motherboard tray 2 3.5&q

6 1.2 CHASSIS SPECIFICATIONS CHASSIS TYPE Mid Tower CHASSIS COLOR Yellow / Black Blue / Black Red / Black DIMENSIONS - 20.4” (H) x 8.7

7 I. Case thumbscrew (long) J. Case thumbscrew (short) K. Power supply mount release screw L. 5.25” drive rail mounting screw M. Rear pan

8 HARDWARE INSTALLATION SECTION 2

9 2.1 SETTING UP 1. Put the chassis upright on a flat, stable surface so that the rear panel (power supply and expansion slots) is facing you. Rem